Get A Quote Now

Natture

Tadelakt microcement of superior resistances | Natture

With Natture we return to the origin to look to the future. We go back to the beginnings of tadelakt in Morocco over two millennia ago to offer a harder, more sustainable and more workable coating. A microcement with the Topciment® guarantee to create decorative finishes for life. Bicomponent lime-based microcement that stands out for its lower shrinkage and higher chemical and mechanical resistances. Continuous low-thickness and top-hardness coating for floors and walls. Natture illustrates the artisanal aspect of tadelakt. A microcement of unparalleled beauty that evokes tadelakt but also exposed concrete, given its wide decorative finishes. Product of attractive natural and material, applicable in trowel and totally reviewable. Luxury, quality, distinction and demonstrable resistance between 1 and 3 mm thick.

How to apply Natture tadelakt microcement on floors

Step 1. Preparation of the support
Adapt the pavement, ensuring that the support is consolidated, in good planimetry conditions, clean and free of grease.
Each application requires a specific solution. Use, depending on the floor in question, the corresponding primer: Primacem Plus, Primacem Abs or Primapox®100 Barrier.
Before applying the Natture tadelakt mortar, use a flexible Builtex fibre mesh to prevent cracks and fissures.
Pour the Acricem resin into a container and pigment until a homogeneous finish is achieved (see proportions in technical sheet). Add the Natture mortar and mix at low revolutions for at least 4 minutes.
Depending on the support and the finish that is intended to be acquired, apply 2 coats of the tadelakt microcement preparation Natture XL or Natture L with a metal trowel (4 hours of drying between coats). Sand each coat with 40-grain sandpaper.
Finish decorating the floor with a coat of our tadelakt microcement Natture. Depending on the desired finish, choose between granulometries M, XL or L. Allow to dry for 4 hours between coats. Sand with 40 grit sandpaper (XL and L) or with 80 grit sandpaper (M).
Proceed to seal the pavement between 24 and 48 hours later. Apply two coats of the Presealer primer (4 hours between coats) and, afterwards, another two coats of any Topsealer WT varnish (24 hours between coats).

How to apply Natture tadelakt microcement on walls

Step 1. Conditioning of the support
Prepare the wall, ensuring that the surface is consolidated, clean and free of grease.
Use the most suitable primer according to the wall. Use one of the following adhesion promoters: Primacem Plus, Primacem Abs or Primapox®100 Barrier.
In a container add the Acricem resin (check proportions in technical data sheet) and pigment until a homogeneous finish is obtained. Incorporate the Natture mortar and mix at low revolutions for at least 4 minutes.
In the same way as it happens on floors, choose between our tadelakt microcement Natture XL and Natture L and apply 2 layers of product using a metal trowel (4 hours of drying between layers). Sand each layer with 40-grain sandpaper.
Finish decorating the wall with 1 coat of the tadelakt microcement of your choice, depending on whether you want to achieve a more exposed concrete, stone, stucco, etc. finish. Opt for Natture XL, Natture L, Natture M or Natture S. Use 40 grit sandpaper (XL and L), 80 grit (M) or 220 grit (S) after each coat. Allow to dry for 4 hours between coats.
24-48 hours later, seal the wall with 2 coats of the Presealer primer (4 hours between coats) and, subsequently, with another two coats of one of our Topsealer WT varnishes (24 hours between coats).

Contact Us Now